iftab(5) -- Linux man page
NAME
iftab - static information about the network interfaces
DESCRIPTION
The file
/etc/iftab
contains descriptive information about the various network interfaces.
iftab
is only used by the program
ifrename(8)
to assign a consistent network interface name to each network interface.
/etc/iftab
defines a set of
mappings.
Each mapping contains an interface name and a set of selectors. The
selectors allow
ifrename
to identify each network interface on the system. If a network
interface matches all descriptors of a mapping,
ifrename
attempt to change the name of the interface to the interface name
given by the mapping.
MAPPINGS
Each mapping is described on a separate line, it starts with an
interface name,
and contains a set of
descriptors,
separated by space or tabs.
The relationship between descriptors of a mapping is a
logical and.
A mapping matches a network interface only is all the descriptors
match. If a network interface doesn't support a specific descriptor,
it won't match any mappings using this descriptor.
If you want to use alternate descriptors for an interface name
(logical or), specify two different mappings with the same interface
name (one on each line).
Ifrename
always use the first matching mapping starting from the
end
of
iftab,
therefore more restrictive mapping should be specified last.
INTERFACE NAME
The first part of each mapping is an interface name. If a network
interface matches all descriptors of a mapping,
ifrename
attempt to change the name of the interface to the interface name
given by the mapping.
The interface name of a mapping is either a plain interface name (such as
eth2 or wlan0)
or a interface name pattern containing a single wildcard (such as
eth* or wlan*).
In case of wildcard, the kernel replace the '*' with the lowest
available integer making this interface name unique.
DESCRIPTORS
Each descriptor is composed of a descriptor name and descriptor
value. Descriptors specify a static attribute of a network interface,
the goal is to uniquely identify each piece of hardware.
Most users will only use the
mac
selector, other selectors are for more specialised setup.
- mac mac address
-
Matches the MAC Address of the interface with the specified MAC
address. The MAC address of the interface can be shown using
ifconfig(8)
or
ip(8).
The specified MAC address may contain a '*' for wilcard matching.
This is the most common selector, as most interfaces have a unique MAC
address allowing to identify network interfaces without ambiguity.
- arp arp type
-
Matches the ARP Type (also called Link Type) of the interface with the
specified ARP type. The ARP Type of the interface can be shown using
ifconfig(8)
or
ip(8).
This selector is useful when a driver create multiple network
interfaces for a single network card.
- driver driver name
-
Matches the Driver Name of the interface with the specified driver
name. The Driver Name of the interface can be shown using
ethtool -i(8).
- businfo bus information
-
Matches the Bus Information of the interface with the specified bus
information. The Bus Information of the interface can be shown using
ethtool -i(8).
- baseaddress base address
-
Matches the Base Address of the interface with the specified base
address. The Base Address of the interface can be shown using
ifconfig(8).
Because most cards use dynamic allocation of the Base Address, this
selector is only useful for ISA and EISA cards.
- irq irq line
-
Matches the IRQ Line (interrupt) of the interface with the specified
IRQ line. The IRQ Line of the interface can be shown using
ifconfig(8).
Because there are IRQ Lines may be shared, this selector is usually
not sufficient to uniquely identify an interface.
- iwproto wireless protocol
-
Matches the Wireless Protocol of the interface with the specified
wireless protocol. The Wireless Protocol of the interface can be shown
using
iwconfig(8).
This selector is only supported on wireless interfaces and is not
sufficient to uniquely identify an interface.
EXAMPLE
# This is a comment
eth2 mac 08:00:09:DE:82:0E
eth3 driver wavelan interrupt 15 baseaddress 0x390
eth4 driver pcnet32 businfo 0000:02:05.0
air* mac 00:07:0E:* arp 1
AUTHOR
Jean Tourrilhes - jt@hpl.hp.com
FILES
/etc/iftab
SEE ALSO
ifrename(8),
ifconfig(8),
ip(8),
iwconfig(8).
|
Current Users : 13 (Member 0)
Write for us and get publicity, link to your website, and best of all get
paid. Please visit our 
